Home › Tile Calculator
Tile Calculator
On this page
Tile calculator
An assumption you can change: see the planning ranges below.
One tile covers width × length ÷ 144 sq ft. Tiles and boxes are rounded up. The waste % is a planning assumption; check the box label for tiles or sq ft per box.
Tile is sold by the box but laid one piece at a time, so a good estimate needs three numbers: the area, the size of one tile, and how much extra to allow for cuts and breakage. The calculator does the arithmetic. The rest of this page explains each input and gives a tile-count table for common sizes.
The formula
- Area of one tile (sq ft) = tile width (in) × tile length (in) ÷ 144
- Area to buy = surface area × (1 + waste % ÷ 100)
- Tiles = area to buy ÷ area of one tile, rounded up
- Boxes = tiles ÷ tiles per box, rounded up
The calculation uses the tile's face size and ignores grout joints. Grout lines take up a little of the surface, so the count comes out slightly high, which is the safe direction.
Worked example 1: bathroom floor, 150 sq ft, 12 × 24 in tile
- One tile: 12 × 24 ÷ 144 = 2 sq ft
- With 10% waste: 150 × 1.10 = 165 sq ft
- Tiles: 165 ÷ 2 = 82.5, so 83 tiles
- If the box holds 8 tiles: 83 ÷ 8 = 10.4, so 11 boxes (88 tiles)
Worked example 2: kitchen backsplash, 30 sq ft, 3 × 6 in subway tile
- One tile: 3 × 6 ÷ 144 = 0.125 sq ft, so 8 tiles per sq ft
- With 10% waste: 30 × 1.10 = 33 sq ft
- Tiles: 33 ÷ 0.125 = 264 tiles
For a wall, measure each tiled section as its own rectangle (width × height). Subtract the window or range-hood opening only if it's large. A small outlet cutout doesn't save a tile, it just means cutting one.
Tiles per square foot by tile size
Geometry only (144 ÷ tile area in square inches). Multiply by your area with waste to get a tile count.
| Tile size (in) | Sq ft per tile | Tiles per sq ft |
|---|---|---|
| 3 × 6 (subway) | 0.125 | 8 |
| 4 × 4 | 0.111 | 9 |
| 6 × 6 | 0.25 | 4 |
| 4 × 12 | 0.333 | 3 |
| 6 × 24 (plank) | 1 | 1 |
| 12 × 12 | 1 | 1 |
| 18 × 18 | 2.25 | 0.444 |
| 12 × 24 | 2 | 0.5 |
| 8 × 48 (plank) | 2.667 | 0.375 |
| 24 × 24 | 4 | 0.25 |
| 24 × 48 | 8 | 0.125 |
Mosaic sheets are counted by the sheet, not the chip. Use the sheet's coverage, often printed on the box, as the "tile" size.
Choosing a waste percentage
There's no single official waste figure for tile, so the calculator treats waste as your assumption and starts at 10%. Our flooring waste guide explains the planning ranges this site uses: about 10% for tile laid straight in an average room, about 15% for diagonal layouts, and 15–20% or more for herringbone. These are planning guidance, not a standard. Raise the figure if:
- the room has many corners, doorways or a toilet and vanity to cut around,
- the tile is large-format in a small room, so offcuts are rarely reusable,
- the tile is hard to cut (thick porcelain, natural stone), or
- you want spare tiles from the same production run for future repairs.
If the tile's own installation guide or your installer gives a figure, use that instead.
Buying by the box
Boxes list either tiles per box or square feet per box. If you know square feet per box, divide the area-to-buy by that and round up. In example 1, if a box covers 15.5 sq ft: 165 ÷ 15.5 = 10.6, so 11 boxes.
Check that every box comes from the same lot or batch. Shade and size can vary slightly between production runs, which is why spares from your own lot are worth keeping.
FAQ
How many tiles do I need for 100 square feet?
It depends on the tile size. With 12 × 12 tiles and 10% waste: 110 tiles. With 12 × 24 tiles and 10% waste: 110 ÷ 2 = 55 tiles.
How do I calculate tiles for a wall?
Measure each wall section as width × height in feet, add the sections together, subtract large openings, then follow the same steps as a floor.
Does grout spacing change the tile count?
Slightly. Ignoring grout joints, as this calculator does, gives a small overestimate, which errs on the safe side.
What waste percentage should I use for tile?
That's your call. Around 10% is a common planning figure for straight layouts, with more for diagonal or herringbone. The calculator lets you set any percentage.
How many 3 × 6 subway tiles are in a square foot?
8, because each tile is 18 square inches and a square foot is 144 square inches.
This site is owned and operated by calcsqft.com.
Sources
- Tile counts and box math: geometry (144 sq in = 1 sq ft).
- Waste percentages: this site's own planning ranges (see the flooring waste factor guide). They're an adjustable planning assumption you can change, not a sourced standard.
Cite this page: Pierre Mentor, “Tile Calculator,” CalcSqft.com, updated Nov 10, 2026, https://calcsqft.com/tile-calculator/
