Home › Guides › Flooring Waste Factor: How Much Extra Flooring to Buy
Flooring Waste Factor: How Much Extra Flooring to Buy
On this page
The floor area of a room is never the amount of flooring you need. Every row ends with a cut, every doorway and vent needs a notch, and a few pieces in any order arrive chipped or simply look wrong next to their neighbours. The extra you buy to cover all of that is the waste factor (or overage), expressed as a percentage of the floor area.
The flooring calculator has a quick table of typical percentages. This guide explains where those numbers come from, so you can tell when your project needs more or less than the default and avoid both a second trip to the store and five spare boxes in the garage.
The formula
Material to buy = floor area × (1 + waste % ÷ 100), then round up to whole boxes.
For a 180 sq ft bedroom:
| Waste factor | Material to buy |
|---|---|
| 5% | 189.0 sq ft |
| 7% | 192.6 sq ft |
| 10% | 198.0 sq ft |
| 15% | 207.0 sq ft |
| 20% | 216.0 sq ft |
Rounding up to full cartons adds a little more. If your vinyl plank comes in cartons that cover 23.4 sq ft (use the number printed on your carton), 198 sq ft ÷ 23.4 = 8.46, so you buy 9 cartons, or 210.6 sq ft. That rounding is part of why careful buyers don't pick a high waste percentage and round up generously. The two stack.
Where the waste actually goes
Knowing what creates offcuts tells you which way to adjust the percentage.
- End-of-row cuts. Plank floors are laid in rows, and the last plank in each row is cut to fit. The offcut can often start the next row, which is why straight plank layouts waste relatively little.
- Stagger rules. Most plank products require the end joints in neighbouring rows to be offset by a minimum distance, set in the installation instructions. Offcuts shorter than that minimum can't be reused, so short rooms and long planks produce more scrap.
- Obstacles. Door jambs, floor vents, kitchen islands, pipes and fireplace hearths each need custom cuts. A plain rectangle has none; a kitchen can have a dozen.
- Angles. Anything laid at an angle to the walls (diagonal tile, herringbone, chevron) produces a triangular offcut at every wall, and triangles rarely fit anywhere else.
- Defects and selection. Some boards have damaged tongues, and installers set aside pieces that don't blend. This is a small share, but it's never zero.
- Spares for future repairs. Product lines are discontinued and dye lots vary between production runs. A box kept back from the same lot is the only reliable way to repair a damaged plank or tile years later.
Adjusting for your room
The typical ranges below are planning guidance, the same as in the calculator. When a manufacturer or your installer recommends a specific overage, use theirs.
| Situation | Typical overage | Why |
|---|---|---|
| Large, open, rectangular room, straight plank lay | 5–10% | Offcuts start the next row; few obstacles |
| Average room with a closet, doorways and some cuts | about 10% | The common default |
| Small rooms, halls, closets, many doorways | 10–15% | Short rows mean short offcuts that can't meet the stagger rule |
| Tile laid straight | about 10% | Cuts at every wall; tile can break during cutting |
| Diagonal tile or diagonal plank | 15% | Triangular offcuts at every wall |
| Herringbone or chevron | 15–20% or more | Every perimeter piece is an angled cut |
Three things push you toward the higher end within any row of that table:
- Large pieces in a small room. A 24 × 48 in tile in a 5 × 8 ft bathroom leaves offcuts too big to throw away but the wrong shape to use. Small mosaics on mesh waste very little.
- Long planks in short rooms. A 72 in plank in a 6 ft wide hall leaves almost every offcut too short to start the next row.
- A pattern repeat. Wood-look tile and some vinyl products have a limited number of distinct faces. To avoid placing identical planks side by side you may skip pieces, and that uses material.
Worked example: bathroom tile
A bathroom floor measures 120 sq ft and will be tiled with 12 × 24 in tiles laid straight.
- Each tile covers 12 × 24 ÷ 144 = 2 sq ft.
- With 10% waste: 120 × 1.10 = 132 sq ft ÷ 2 = 66 tiles.
- If the tile comes 8 to a carton: 66 ÷ 8 = 8.25, so 9 cartons (72 tiles).
Change the layout to diagonal at 15% and you need 120 × 1.15 = 138 sq ft, or 69 tiles. That still fits in 9 cartons, so the diagonal layout costs you no extra boxes here. That doesn't always happen, but it's worth checking before you rule out a layout on cost. The home page has a tile counter for this, and the flooring calculator handles the carton rounding.
Worked example: herringbone hall
A 200 sq ft hallway in herringbone with cartons that cover 20 sq ft:
- At 15%: 200 × 1.15 = 230 sq ft → 230 ÷ 20 = 11.5 → 12 cartons
- At 20%: 200 × 1.20 = 240 sq ft → 240 ÷ 20 = 12 → 12 cartons
Both overages land on the same order, which gives you the higher margin for free. When two waste percentages round to the same number of cartons, use the higher one.
Worked example: carpet and roll width
Carpet is the exception to percentage rules, because it comes off a roll of fixed width (12 ft is common). Waste depends on how the room's dimensions fit that width, not on a percentage.
Take a 14 × 18 ft room (252 sq ft). A 12 ft roll covers only 12 ft of the room's width either way, so you need a seam:
- Running the roll along the 14 ft side: one 12 × 14 ft piece covers 12 ft of the 18 ft length. The remaining 6 × 14 ft strip comes from a second 12 × 14 ft cut, split in half. You buy 12 × 28 ft = 336 sq ft (37.33 sq yd), about 33% more than the floor area, and keep a 6 × 14 ft remnant.
- Running it along the 18 ft side: one 12 × 18 ft piece plus a 2 ft strip. Cutting that strip from a second full-width length means buying 12 × 36 ft = 432 sq ft (48 sq yd), unless the strip can be pieced from shorter cuts. Pile direction and seam placement rules usually limit that.
The first layout is clearly cheaper here, but real carpet orders also depend on pile direction, pattern match and where the seams can go. Treat this arithmetic as a way to understand a quote, and let the retailer's measurement set the order.
Buy once, as one order
- Combine rooms into one order. Two rooms of 130 and 95 sq ft at 10% need 8 + 6 = 14 cartons of 20 sq ft if you calculate them separately, but only 13 cartons together (225 × 1.10 = 247.5 sq ft). Offcuts from one room can finish the other.
- Buy everything from the same production lot, and check the lot numbers on the cartons before installing.
- Open and blend. Installers often pull planks from several cartons at once to mix colour variation. That's another reason to have all the material on site before starting.
- Check the return policy. Many stores accept unopened cartons back, which makes erring slightly high less costly than running short and finding the lot is gone.
FAQ
What waste factor should I use for vinyl plank or laminate?
About 10% for a typical room laid straight, 5–7% for a large, simple rectangle, and 15% if it's laid diagonally. Follow the product's installation guide if it states a figure.
Is 10% waste enough for tile?
For straight layouts with standard-size tile in an average room, usually yes. Go to 15% for diagonal layouts, large-format tile in small rooms, or tile that is hard to cut.
Why does herringbone need so much extra?
Every piece that meets a wall is cut at an angle, and those triangular offcuts can rarely be used anywhere else.
Should I keep leftover flooring?
Yes. Keeping one unopened carton from the same lot is the most practical way to repair damage later, since product lines and colours change.
Do I add waste to carpet?
Not as a percentage. Carpet waste comes from fitting fixed roll widths to your room, so it depends on room dimensions and seam layout. Ask the retailer to measure.
Cite this page: Pierre Mentor, “Flooring Waste Factor: How Much Extra Flooring to Buy,” CalcSqft.com, updated Nov 10, 2026, https://calcsqft.com/guides/flooring-waste-factor/
